2014年3月3日星期一

The Structure of Shale Shaker

Solids control is a technique used in drilling rig to separate the solids in the drilling fluids that are crushed by the drill bits and carried out of the well surface. Normally solid control system is consist of five stages, including mud tank, shale shaker, vacuum degasser, desander, desilter, centrifuge. Shale shaker is used to separate the big solids with diameter above 75μm, and 45~74μm for desander, and 15~44μm for desilter. Sometimes desander & desilter are combined as high efficient mud cleaner. When air enters into the drilling fluids, vacuum degasser is used to separate the air. If no air in the mud, the degasser would work as a big agitator. All these equipments are mounted on the top of the mud tank. After separating the solids, the clean mud would be pumped into the borehole again.

The shale shaker is the first stage of solids control equipment in drilling purification system. It can remove cuttings above 75μm brought from the drilling well to leave the liquid with smaller particles into the tanks below, which will flow into next grade solids control equipment to be treated.
Shale shakers consist of the following parts:
Hopper - The Hopper, commonly called the "base" serves as both a platform for the shaker and collection pan for the fluid processed by the shaker screens, also known as "underflow". The hopper can be ordered according to the needs of the drilling fluid, aka "mud" system. It can come in different depths to accommodate larger quantities of drilling fluid as well as have different ports for returning the underflow to the mud system.
Feeder- The Feeder is essentially a collection pan for the drilling fluid before it is processed by the shaker, it can come in many different shapes and sizes to accommodate the needs of the mud system. The most commonly used feeder is known as the weir feeder, the drilling fluid enters the feeder usually through a pipe welded to the outside wall near the bottom of the feeder tank, it fills the feeder to a predetermined point and like water flowing over a dam the mud (drilling fluid) spills over the weir and onto the screening area of the shaker. This method of feeding the shaker is most widely used due to its ability to evenly distribute the mud along the entire width of the shaker allowing for maximum use of the shaker's screening deck area.
Some feeders can be equipped with a bypass valve at the bottom of the feeder which allows the drilling fluid to bypass the shaker basket and go directly into the hopper and back into the mud system without being processed by the shaker screens.
Screen Basket- Also known as the screen "bed" it is the most important part of the machine, it is responsible for transferring the shaking intensity of the machine, measured in "G's", while keeping the "shaking" motion even throughout the entire basket. It must do all that while holding the screens securely in place, eliminating drilled solids bypass to the hopper and allowing for easy operation and maintenance of the machine. Different brands of shakers have different methods of fulfilling these demands by using specialized screen tensioning apparatus, rubber seals around the screens, basket reinforcement to limit flex, rubber Float Mounts rather than springs, rubber Deck seals and selective vibrator placement.
Basket Angling Mechanism- The shaker basket must be capable of changing its angle to accommodate various flow rates of drilling fluids and to maximize the use of the shaker bed, this is where the angling mechanism plays an important part.
Vibrator- This is the device which applies the vibratory force and motion type to the shaker bed. A vibrator is a specialized motor built for the purpose of vibrating, While containing an electric motor to provide the rotary motion it uses a set of eccentric weights to provide an omnidirectional force. To produce the proper Linear motion a second, counter rotating, vibrator is added in parallel to the first. This is what gives us the linear motion, "high G" shaking of the basket.

Tangshan Aojie Petroleum Machinery Equipment Make Co., Ltd (Short for:
OGEM Solids Control)
Address: NO.2 Jingxi Road,Lunan District,Tangshan city,Hebei
province,China
Tel: 86-315-8676484
Fax: 86-315-2648099
Zip Code: 063000
Email: ogem2@ogemsolidscontrol.com
Website: http://www.ogemsolidscontrol.com/
Skype:burning_lee                              


OGEM Solids Control is main professional manufacturer of Solids Control System in China, OGEM  is a vital part of the world hydrocarbon exploration and production industry, as well as one of top three solids control equipment suppliers in China, which offers its products for CNPC, CNOOC ,HH, Gazprom, RG, etc . If you want to know more information about solid control system and oil drilling solids control equipment,you can contact us online.

没有评论:

发表评论