Advance planning increases effectiveness and efficiencyBaroid’s engineered waste management solutions are customized to maximize drilling efficiency. That customization delivers different solids control systems for a variety of waste management needs. Our engineers collaborate with you to fully understand your project priorities. These discussions enable us to customize the solids control system that will best meet the specific demands of your drilling program. Whether your goal is meeting compliance regulations for overboard discharge, reducing waste or water, lowering the cost of waste transportation, or maintaining effective solids control while achieving high ROP in offshore drilling, Baroid will engineer a solids control program to meet the operational specifications and environmental needs of your drilling program.
Maximum solids removal maximizes cost savingsEfficiently removing unwanted solids from the circulating system helps ensure the highest quality drilling fluid in your wells. Improved solids control efficiency translates into less replacement fluid, fewer additives, less waste (solid and liquid) to be transported and disposed of, and less risk of hole problems related to excessive solids content in the drilling fluid.
Maintaining drilling fluid properties enables optimal efficiencyEffectively removing unwanted solids from the drilling fluid on the first pass through the solids control equipment is an important factor in maintaining drilling fluid properties and reducing drilling fluid cost. Baroid utilizes the highest quality solids control equipment in all our operations. Rigorous integrated operational and technical processes, in addition to our Mainstay Process approach to customization, allows us to determine in advance problems that might occur and often how to avoid them altogether. The more we know about your goals and challenges up front, the better our customized solids control solution will serve your specific drilling program.
Centrifuges
Maximize solids removal the first time throughCentrifuges are used towards the end of the solids control system, removing the finer drill solids from the drilling fluid. Maximum solids removal is imperative early on, before the active fluid system returns down hole to collect more solids and further break apart into finer solids affecting the density or weight of the fluid system. Baroid provides high capacity decanting centrifuges help ensure maximum separation of fluids and solids.
Flexible technology to meet operational and throughput needsIn weighted fluid systems Baroid centrifuges can be used to control the rheological properties of the fluid by recovering barite through adjustable bowl speed and centrifugal force. Barite and necessary weighting agents are allowed to remain in the active system and continue to circulate. Baroid helps select the right centrifuge in conjunction with all solids control equipment after extensive evaluation of the project needs. We consider environmental regulations, fluid plan, target ROP and more. Our capable engineers are available for maintenance needs, expert waste management advice and can keep the project running with minimal NPT. The centrifuges we provide are designed with easy access to normal wear parts for fast and easy maintenance.
Cuttings Dryers
Reduce environmental impact and meet compliance regulationsAs regulations on drilling waste become more stringent operators are in need of a reliable waste disposal solution that ensures the waste and the liability of its impact are gone for good. Baroid’s V-133 and V-77 cuttings dryers can offer a reliable solution by reducing the oil on cuttings ratio of oil-based fluids to an acceptable limit for waste disposal.
Maximize separation to maximize savingsHalliburton Baroid’s V-133 vertical cuttings dryer was designed to provide efficient throughput for high ROP operations. Its high capacity processing provides substantial reduction to the oil-on-cuttings ratio to help meet compliance regulations for waste disposal. Maximum separation of solids and liquids can be achieved. Increased separation means increased fluid recovery, lower cost of replacement fluid and minimal waste to be transported and disposed of, going straight to your bottom line. The V-77 dryer is similar in design to the V-133 but has a smaller footprint and lower power requirement, ideal for lower ROP operations and more constrained rig space.
Integrated and customized packages to meet your needsLow gravity solids and other waste can ruin the integrity of the circulating system. Baroid’s cuttings dryers are one piece of the solids control system designed to remove solids and keep your operation running smoothly. Baroid adheres to our rigorous mainstay process to design, test and implement the right solids control system for your rig.
Dewatering Systems
Improve water conservation and minimize environmental impactAs water conservation becomes a greater public concern, the amount of water used in drilling operations has also come under scrutiny. Fortunately, Baroid dewatering systems allow you to both recycle water and reduce the amount of waste transported and disposed of in the environment.
Baroid uses both chemical and mechanical means to separate water from suspended solids. With our ENVIRO-FLOC® dewatering system, coagulation and flocculation are applied to the fluid to chemically remove fine solids. In addition, a decanting centrifuge employs mechanical separation, all in a versatile, mobile and winterized unit.
Recycle to reduce costsThe ENVIRO-FLOC system, and dissolved air flotation (DAF) units, can be used onsite to treat and recycle water as part of the solids control system, or to reduce total waste volume for subsequent disposal. Reclaimed water can then be reused in the drilling fluid, reducing fresh water consumption and costs, as well as reducing costly transport.
Versatile units, customized to meet project needsOur high capacity, ENVIRO-FLOC system can process up to 300 gallons per minute, a capability that can allow high ROP operations to continue. Plus, its versatile design allows it to be fitted onto skids or trailers for full mobility and, because it is winterized, can be used in extremely cold conditions. Baroid engineers can design the entire waste management system around your specific operational requirements. Integration of the unit and each piece of equipment with the waste management system is provided via Baroid’s proven processes.
Any requirements, please contact with us freely!
Tangshan Aojie Petroleum Machinery Equipment Make Co., Ltd (Short for: OGEM Solids Control)
Address: NO.2 Jingxi Road,Lunan District,Tangshan city,Hebei province,China
Tel: 86-315-8676484
Fax: 86-315-2648099
Zip Code: 063000
Email: ogem2@ogemsolidscontrol.com
Website: http://www.ogemsolidscontrol.com/
Need any lateast news about the Hydrocyclone desender or other oilfield equipment,please enter in our website. WELCOME!!!
没有评论:
发表评论